Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Initialising ...
Nagai, Haruyasu; Furuta, Yoshihiro*; Nakayama, Hiromasa; Satoh, Daiki
Journal of Nuclear Science and Technology, 60(11), p.1345 - 1360, 2023/11
Times Cited Count：0 Percentile：0.01(Nuclear Science & Technology)A novel monitoring method for the quantitative visualization of 3D distribution of a radioactive plume and source term estimation of released radionuclides is proposed and its feasibility is demonstrated by preliminary test. The proposed method is the combination of gamma-ray imaging spectroscopy with the Electron Tracking Compton Camera (ETCC) and real-time high-resolution atmospheric dispersion simulation based on 3D wind observation with Doppler lidar. The 3D distribution of a specific radionuclide in a target radioactive plume is inversely reconstructed from line gamma-ray images from each radionuclide by several ETCCs located around the target by harmonizing with the air concentration distribution pattern of the plume predicted by real-time atmospheric dispersion simulation. A prototype of the analysis method was developed, showing a sufficient performance in several test cases using hypothetical data generated by numerical simulations of atmospheric dispersion and radiation transport.
Fukuda, Kodai; Yamane, Yuichi
Proceedings of 12th International Conference on Nuclear Criticality Safety (ICNC2023) (Internet), 9 Pages, 2023/10
This study presents the results of multiphysics analysis, which investigates the change of reactivity caused by the motion of fluids, of Windscale Works criticality accident. The purpose of this study is to confirm previously reported trends of emulsion formation and increase in reactivity by the multi-physics analysis which takes the motion of fluids into account. Continuous energy Monte Carlo code MVP3 was used to calculate reactivity based on the material distribution obtained by CFD calculation using OpenFOAM. An interface program in python was developed to transfer data from OpenFOAM to MVP3. The change of reactivity caused by the motion of solutions was calculated without considering the generation of heat by fissions in a system that simulated the transfer vessel at Windscale Works. As a result, trends of emulsion formation and increase in reactivity were confirmed. The influence of the resolution of the calculation system on the results was also discussed.
Terada, Atsuhiko; Nagaishi, Ryuji
Nuclear Science and Engineering, 197(4), p.647 - 659, 2023/04
Times Cited Count：2 Percentile：31.61(Nuclear Science & Technology)In order to understand dispersion of hydrogen leaked in a partially open space practically, which can be considered as a basic model for all processes of transfer, treatment, storage and disposal of radioactive materials containing fuel debris in the decommissioning of nuclear facilities after a severe accident, by using a CFD code, the effects of vent size and outer wind on the H
dispersion were analytically studied by adopting the experimental Hallway model, which has H release hole on the ceiling, one vent on the Roof vent and Door vent. Air flowed in the model from the Door vent, while H was discharged outside from the Roof vent. The discharged amount of H increased in conjunction with the air inflow when the size of Roof and or Door vents was increased. The effect of wind depended on the direction to the Door vent: wind from the same direction as the Door vent promoted the H discharge, while wind from the opposite direction suppressed. The dispersion characteristics of indoor leaked H was clarified for comparing model tests with the same Froude number and different scales. It was found from the analysis results of comparing model tests with the same Froude number and different scales that when the H leaked into the room and diffused to the air, the flow generated by the buoyancy of mixed gas created the stack effect which caused the natural ventilation by drawing in the air from the outside through vent. In addition, it was speculated that the H concentration decreased after its leak by quickly mixing with the air which flowed in from the vents and reached to the floor due to the Coanda effect, which is the effect of the free jet being drawn to a nearby wall.
Nakano, Keita; Iwamoto, Hiroki; Nishihara, Kenji; Meigo, Shinichiro; Sugawara, Takanori; Iwamoto, Yosuke; Takeshita, Hayato*; Maekawa, Fujio
JAEA-Research 2021-018, 41 Pages, 2022/03
JAEA-Research-2021-018.pdf:2.93MB
Neutronic analysis of beam window of the Accelerator-Driven System (ADS) proposed by Japan Atomic Energy Agency (JAEA) has been conducted using PHITS and DCHAIN-PHITS codes. We investigate gas production of hydrogen and helium isotopes in the beam window, displacement per atom of beam window material, and heat generation in the beam window. In addition, distributions of produced nuclides, heat density, and activity are derived. It was found that at the maximum 12500 appm H production, 1800 appm He production, and damage of 62.1 DPA occurred in the beam window by the ADS operation. On the other hand, the maximum heat generation in the beam window was 374 W/cm
. In the analysis of LBE, 
Bi and 
Po were found to be the dominant nuclides in decay heat and radioactivity. Furthermore, the heat generation in the LBE by the proton beam was maximum around 5 cm downstream of the beam window, which was 945 W/cm.
Maekawa, Fujio
JPS Conference Proceedings (Internet), 33, p.011042_1 - 011042_6, 2021/03
Development of beam window (BW) materials is one of crucial issues in development of accelerator driven nuclear transmutation systems (ADS). The BW is exposed to high energy protons and spallation neutrons, and also to corrosive lead-bismuth eutectic (LBE) alloy at high temperature of about 500
C. Recently, not only high-power accelerators but also high-power targets are the rate-limiting factor for increasing the power of accelerator facilities in terms of radiation damage and heat removal. To study radiation damage on BW and target materials for high-power accelerator facilities including ADS, we are planning a materials irradiation facility by utilizing the proton beam of 400 MeV and 250 kW provided by the J-PARC's Linac. The target is flowing LBE alloy which is a candidate target and coolant material of ADS. When a steel sample is irradiated in the target for one year, the sample receives radiation damage of about 10 dpa at maximum which is equivalent to the yearly radiation damage of ADS's BW. In the current facility concept, the facility is equipped with a hot-laboratory for efficient post-irradiation examination. The facility will be outlined in this presentation.
Sugawara, Takanori; Takei, Hayanori; Iwamoto, Hiroki; Oizumi, Akito; Nishihara, Kenji; Tsujimoto, Kazufumi
Progress in Nuclear Energy, 106, p.27 - 33, 2018/07
Times Cited Count：16 Percentile：85.18(Nuclear Science & Technology)The Japan Atomic Energy Agency (JAEA) has investigated an accelerator-driven system (ADS) to transmute minor actinides which will be partitioned from the high level waste. There are various inherent issues for the research and development on the ADS. The recent two activities to realize a feasible and reliable ADS concept are introduced in this paper. For the feasibility, the design of a beam window which is a boundary of the accelerator and the subcritical core, is one of the most important issues. To mitigate the design condition of the beam window, namely to reduce the proton beam current, the subcritical core concept with subcriticality adjustment rods were investigated. For the reliability, the beam-trip is the inherent and serious issue for the ADS design because it induces rapid temperature change to coolant and structures in the subcritical core. To improve the beam-trip frequencies, a double-accelerator concept was proposed and its beam-trip frequency was estimated.
Iwamoto, Hiroki; Nishihara, Kenji; Iwamoto, Yosuke; Hashimoto, Shintaro; Matsuda, Norihiro; Sato, Tatsuhiko; Harada, Masahide; Maekawa, Fujio
Journal of Nuclear Science and Technology, 53(10), p.1585 - 1594, 2016/10
Times Cited Count：18 Percentile：85.7(Nuclear Science & Technology)Sasa, Toshinobu; Takei, Hayanori; Saito, Shigeru; Obayashi, Hironari; Nishihara, Kenji; Sugawara, Takanori; Iwamoto, Hiroki; Yamaguchi, Kazushi; Tsujimoto, Kazufumi; Oigawa, Hiroyuki
NEA/CSNI/R(2015)2 (Internet), p.85 - 91, 2015/06
Nuclear transmutation got much interested as an effective option of nuclear waste management. Japan Atomic Energy Agency (JAEA) proposes the transmutation of minor actinides (MA) by accelerator-driven system (ADS) using lead-bismuth alloy (Pb-Bi). To obtain the data for ADS design, JAEA plans to build a Transmutation Experimental Facility (TEF) in the J-PARC project. TEF consists of two buildings, an ADS target test facility (TEF-T) with 400MeV-250kW Pb-Bi target, and a Transmutation Physics Experimental Facility (TEF-P), which set up a fast critical assembly driven by low power proton beam with MA fuel. In TEF-T, irradiation test for materials, and engineering tests for Pb-Bi target operation will be performed. Various research plans such as nuclear data measurements have been proposed and layout of the experimental hall are underway. In the presentation, roadmap to establish the ADS transmutor and latest design activities for TEF construction will be summarized.
Allelein, H.-J.*; Auvinen, A.*; Ball, J.*; G
ntay, S.*; Herranz, L. E.*; Hidaka, Akihide; Jones, A. V.*; Kissane, M.*; Powers, D.*; Weber, G.*
NEA/CSNI/R(2009)5, 388 Pages, 2009/12
Kikuchi, Kenji; Takeda, Yasushi*; Obayashi, Hiroo*; Tezuka, Masao*; Sato, Hiroshi
Journal of Nuclear Materials, 356(1-3), p.273 - 279, 2006/09
Times Cited Count：11 Percentile：56.98(Materials Science, Multidisciplinary)Measurements of LBE flow velocity profile were realized in the spallation target model by the ultrasonic Doppler velocity profile technique. Hitherto, it has not yet been done well because both of poor wetting property of LBE with stainless steels and poor performance of supersonic probes at high temperatures. Measurement was made for a return flow in the target model, which has coaxially arranged annular and tube channels. The electromagnetic pump generates LBE flow and the flow rate was measured by the electromagnetic flow meter. Measurement results show that re-circulation occurred near the surface of beam window, which might affect a heat transfer of target container.
analyses with ferromagnetic and plasma rotation effects and wall geometry for a high steady state tokamakKurita, Genichi; Bialek, J.*; Tsuda, Takashi; Azumi, Masafumi*; Ishida, Shinichi; Navratil, G. A.*; Sakurai, Shinji; Tamai, Hiroshi; Matsukawa, Makoto; Ozeki, Takahisa; et al.
Nuclear Fusion, 46(2), p.383 - 390, 2006/02
Times Cited Count：9 Percentile：31.21(Physics, Fluids & Plasmas)It is shown that critical beta is decreased by ferromagnetic effect by about 8% for 
/
2, and denoting the permeability of ferromagnetic wall and vacuum, respectively, for tokamak of aspect ratio 3. The existence of the stability window for resistive wall mode opened by both effects of the toroidal plasma rotation and the plasma dissipation, which was not observed for high aspect ratio tokamak, is found for tokamak of aspect ratio 3. The effect of ferromagnetism on them is also investigated. The critical beta analyses of NCT (National Centralized Tokamak) plasma using VALEN code are started with stabilizing plate and vacuum vessel geometry with finite resistivity, and the results for passive effect of stabilizing plate are obtained. The calculations including stabilizing effect of the vacuum-vessel and also active feedback control are also performed for present design of NCT plasma.
Takahashi, Koji; Illy, S.*; Heidinger, R.*; Kasugai, Atsushi; Minami, Ryutaro; Sakamoto, Keishi; Thumm, M.*; Imai, Tsuyoshi
Fusion Engineering and Design, 74(1-4), p.305 - 310, 2005/11
Times Cited Count：13 Percentile：65.42(Nuclear Science & Technology)A new diamond window with the copper-coated edge for an EC launcher is developed. The diamond window is designed to cool its disk edge. Since Cu is coated at the entire edge, ingress of cooling water into a transmission line in case of failure on the edge is negligible. In addition, corrosion of Al blaze between the edge and the Inconel cuffs can be avoided. A 170GHz, RF transmission experiment equivalent to a MW-level transmission was carried out to investigate the capability of the edge cooling. The transmission power and pulse are 55kW and 3sec, respectively. Temperature increase was 45C and alomost became constant. Thermal calculation with tan
of 4.4
10
and thermal conductivity of 1.9kW/m/K agrees with the experiment. Since tan of the diamond is much higher than the actual one (tan=210
), the temperature increase corresponds to that of 1MW transmission. It concludes that the Cu coating dose not degrade the edge cooling capability and improves the reliability of the diamond window.
test results of a D-shaped Nb
Al CICC coil fabricated with a react-and-wind process for the National Centralized TokamakAndo, Toshinari*; Kizu, Kaname; Miura, Yushi*; Tsuchiya, Katsuhiko; Matsukawa, Makoto; Tamai, Hiroshi; Ishida, Shinichi; Koizumi, Norikiyo; Okuno, Kiyoshi
Fusion Engineering and Design, 75-79, p.99 - 103, 2005/11
Times Cited Count：1 Percentile：10.45(Nuclear Science & Technology)no abstracts in English
Nishitani, Takeo; Sugie, Tatsuo; Morishita, Norio; Yokoo, Noriko*
Fusion Engineering and Design, 74(1-4), p.871 - 874, 2005/11
Times Cited Count：13 Percentile：65.42(Nuclear Science & Technology)no abstracts in English
Oigawa, Hiroyuki; Tsujimoto, Kazufumi; Kikuchi, Kenji; Kurata, Yuji; Sasa, Toshinobu; Umeno, Makoto*; Nishihara, Kenji; Saito, Shigeru; Mizumoto, Motoharu; Takano, Hideki*; et al.
Proceedings of 4th International Workshop on the Utilisation and Reliability of High Power Proton Accelerators, p.325 - 334, 2005/11
The Japan Atomic Energy Research Institute (JAERI) is conducting the research and development (R&D) on the Accelerator-Driven Subcritical System (ADS) for the effective transmutation of minor actinides (MAs). The ADS proposed by JAERI is the 800 MWth, Pb-Bi cooled, tank-type subcritical reactor loaded with (MA+Pu) nitride fuel. The Pb-Bi is also used as the spallation target. In this study, the feasibility of the ADS was discussed with putting the focus on the design around the beam window. The partition wall was placed between the target region and the ductless-type fuel assemblies to keep the good cooling performance for the hot-spot fuel pin. The flow control nozzle was installed to cool the beam window effectively. The thermal-hydraulic analysis showed that the maximum temperature at the outer surface of the beam window could be repressed below 500 C even in the case of the maximum beam power of 30 MW. The stress caused by the external pressure and the temperature distribution of the beam window was also below the allowable limit.
Tsujimoto, Kazufumi; Oigawa, Hiroyuki; Ouchi, Nobuo; Kikuchi, Kenji; Kurata, Yuji; Mizumoto, Motoharu; Sasa, Toshinobu; Nishihara, Kenji; Saito, Shigeru; Umeno, Makoto*; et al.
Proceedings of International Conference on Nuclear Energy System for Future Generation and Global Sustainability (GLOBAL 2005) (CD-ROM), 6 Pages, 2005/10
The Japan Atomic Energy Research Institute (JAERI) has been proceeding with the research and development (R&D) on accelerator-driven subcritical system (ADS). The ADS proposed by JAERI is a lead-bismuth (Pb-Bi) eutectic cooled fast subcritical core with 800 MWth. To realize such an ADS, some technical issues should be studied, developed and demonstrated. JAERI has started a comprehensive R&D program since the fiscal year of 2002 to acquire knowledge and elemental technology that are necessary for the validation of engineering feasibility of the ADS. The first stage of the program had been continued for three years. The program is conducted by JAERI, and many institutes, universities and private companies were involved. Items of R&D are concentrated on three technical areas peculiar to the ADS: (1) superconducting linear accelerator (SC-LINAC), (2) Pb-Bi eutectic as spallation target and core coolant, and (3) subcritical core design and technology. In the present work, the outline and the results in the first stage of the program are reported.
Kogawa, Hiroyuki; Ishikura, Shuichi*; Sato, Hiroshi; Harada, Masahide; Takatama, Shunichi*; Futakawa, Masatoshi; Haga, Katsuhiro; Hino, Ryutaro; Meigo, Shinichiro; Maekawa, Fujio; et al.
Journal of Nuclear Materials, 343(1-3), p.178 - 183, 2005/08
Times Cited Count：8 Percentile：49.16(Materials Science, Multidisciplinary)A cross-flow type (CFT) mercury target with flow guide blades, which has been developed for JSNS, can suppress the generation of stagnant flow region especially near the beam window where the peak heat density is generated due to spallation reaction. Then, a flat type beam window has been applied to the CFT target from the viewpoint of suppressing dynamic stress caused by a pressure wave, which has been estimated with a mercury model of the linear equation of state. The recent experimental results obtained by using a proton beam incidents to mercury led that a cutoff pressure model in the equation of state of mercury caused a suitable dynamic stress with experimental results. Dynamic stress analyses were carried out with the cutoff pressure model, in which the negative pressure less than 0.15 MPa was not generated. The generated dynamic stress in the flat beam window became much larger than that in a semi-cylindrical type window. However, the generated stress in the semi-cylindrical type beam window was over the allowable stress of SS316L under the peak heat density of 668 W/cc. In order to decrease the dynamic stress in the semi-cylindrical beam window, the incident proton beam was defocused to decrease the peak heat density down to 218 W/cm
. As a result, the dynamic stress could be suppressed less than the allowable stress. On the other hand, due to defocus of the proton beam, high heat density was generated on the end of the flow guide blades, which caused high thermal stress exceeding the allowable stress. To decrease the thermal stress, several shapes of the blade ends were studied analytically, which were selected so as not to affect the mercury flow distribution. A simple thin-end blade showed low thermal stress below the allowable stress.
Oigawa, Hiroyuki; Tsujimoto, Kazufumi; Kikuchi, Kenji; Kurata, Yuji; Sasa, Toshinobu; Umeno, Makoto*; Saito, Shigeru; Nishihara, Kenji; Mizumoto, Motoharu; Takano, Hideki*; et al.
EUR-21227 (CD-ROM), p.483 - 493, 2005/00
JAERI is conducting the study on the dedicated transmutation system using the accelerator driven subcritical system (ADS). A subcritical reactor with the thermal power of 800 MW has been proposed. Many research and development activities including the conceptual design study are under way and planned at JAERI to examine the feasibility of the ADS. In the field of the proton accelerator, a superconducting LINAC is being developed. In the field of the spallation target using lead-bismuth eutectic (LBE), material corrosion, thermal-hydraulics, polonium behavior, and irradiation effect on materials are being studied. Moreover, in the framework of the J-PARC project, JAERI plans to construct the Transmutation Experimental Facility (TEF) to study the feasibility of the ADS using a high-energy proton beam and nuclear fuel and to establish the technology for the LBE spallation target and relevant materials.
Takahashi, Koji; Kobayashi, Noriyuki*; Kasugai, Atsushi; Sakamoto, Keishi
Journal of Physics; Conference Series, 25, p.75 - 83, 2005/00
Recent progress of the development on the ITER equatorial EC launcher components, such as the steering mirrors, its drive system, the waveguide components and the diamond vacuum windows, is reported. Thermmo-mechanical analysis of the recent mirror design shows that maximum temperature increase of 187C at the reflecting surface and maximum stress of 242MPa at the inner surface of the cooling tube are obtained. In the cyclic test of the spiral tube mock-up, the cyclic number of 1.310
is succeeded without failure. In the window development, the fabrication of the Cu-coated edge diamond window and the high power transmission test were done. The Cu-coating on the disk edge can avoid water ingress in the launcher (vessel) under the assumption of the crack formation toward edge. Transmission experiment indicative to 1.2MW, was carried out. Temperature increase of 50C agrees with the calculation. It concludes that the Cu-coated window is capable of MW-level transmission and improves its reliability.
Yoshida, Kiyoshi; Takahashi, Yoshikazu; Mitchell, N.*; Bessette, D.*; Kubo, Hiroatsu*; Sugimoto, Makoto; Nunoya, Yoshihiko; Okuno, Kiyoshi
IEEE Transactions on Applied Superconductivity, 14(2), p.1405 - 1409, 2004/06
Times Cited Count：16 Percentile：59.99(Engineering, Electrical & Electronic)The ITER Central Solenoid (CS) is 12m high and 4m in diameter. The CS consists of a stack of 6electrically independent modules to allow control of plasma shape. The modules are compressed vertically by a pre-compression structure to maintain contact between modules. The CS conductor is CIC conductor with NbSn strands and a steel conduit. The CS model coil and insert coil test results have shown that the conductor design must be modified to achieve an operation margin. This required either to increase the cable diameter or to use strand with a higher current capability. A bronze-process (NbTi)Sn strand is proposed to achieve a higher critical magnetic field. A square conduit with a high Mn stainless steel is proposed as it can satisfy fatigue requirements. The inlets are in the high stress region and any stress intensification there must be minimized. The pre-compression structure is composed of 9tie plates to reduce the stress on the cooling pipes. These design proposals satisfy all ITER operational requirements.
